ROADSAFE MIDDLE BLACK SPEED BUMP MALAYSIA

A) Product Name
100% homogeneous Vulcanised EPDM RUBBER SPEED BUMP with locks to prevent dislocation after installation. ( With Cat Eyes Reflective Glass )

B) Brand
RUDSAF ™ ( ROADSAFE ),

MADE IN MALAYSIA
C) Raw Material
Made of 100% homogeneous Vulcanised EPDM Rubber
( No Recycled / Reclaimed Rubber ) & moulded with around 3mm of EPDM Yellow wear layer for the Yellow Part for better visibility.

D) Purpose
1) Control vehicle speeds to promote pedestrian safety

2) Reduce the risk of accidents in parking areas and residential streets

E) Scope
Speed bumps are more aggressive traffic calming options and are helpful in places where pedestrians and cars share space closely, like parking lots and driveways.

F) Characteristics
Our RUDSAF™ meets Australian/New Zealand Standards of “AS/NZS2890.1:2004 Parking Facilities” it determines four main types of criteria for speed Bumps.

Why AS/NZS2890.1:2004 ParkingFacilities?
AS/NZS2890.1:2004 is an Australian/New Zealand Standard that guides specific minimum requirements for the design and layout of off-street car parking.

The content within AS/NZS2890.1:2004 can be pretty comprehensive as our reference.

  Bumps that comply with standards are determined by height, cross-section, markings, and angles below.

Criteria 1 )
Height: Must be between 25 to 75mm.

Criteria 2 )
Cross Section: Must be flat on top of around 100mm ~ 150mm, and Shape cannot in parabolic or peaked.

Criteria 3 )
Ramp Angle: Must have a ramp angle of 2:1

Criteria 4 )
Markings: Must have alternating yellow stripes 250mm wide.

RUDSAF EPDM RUBBER SPEED BUMPS

Why We Choose Homogeneous EPDM Rubber& What are the Benefits of using EPDM Rubber?

i) Homogeneous EPDM Rubber will compress under high impact better than recycled/ reclaimed rubber.

ii) Resistance to UV exposure, ozone, ageing, weathering and many chemicals - excellent for outdoor applications, Do not use EPDM rubber if continual contact with petroleum-based products is required.

iii) Stability in high and low temperatures - EPDM material can be used in severe environmental conditions, and the withstand temperature range from -20⁰F to +300⁰F (-29⁰C to 150⁰C)

iv) Low electrical conductivity

v) Steam and water-resistant

vi) Properties allow it to be widely used and highlyversatile, can be applied successfully in many situations

vii) Used in the proper environment, the parts will work well and last long without breaking down, brittle, etc.

G) SPECIFICATIONS
1) Manufacture from High-Density 100%Homogeneous EPDM Rubber with cat’s eye and “ LOCK “ features to prevent dislocation after installation, an additional advantage for uneven/soft Asphalt ( Tar ) road surface.

2) Available in Black &Yellow combination for greater visibility

3) Anti-skid surface with flattop of 110mm Width as defined under AS/NZS2890.1:2004 Parking Facilities of Criteria 2.

4) All units can purchase separately

5) Sizes :-
i) Model : RSBB250X310, 100% BLACK EPDM Rubber, Middle Black Speed Bumps with Lock,~50mm Thickness, ~310mm Width x ~250mm Length/pc, ~3.3kgs/pc

ii) Model: RSBY250X310, 100% EPDM Rubber with ~3mm Yellow Top Wear Layer, Middle Yellow Speed Bumps with Lock,~50mm Thickness, ~310mm Width x ~250mm Length/pc, ~3.3kgs/pc

iii) Model : RECB250X310, 100% BLACK EPDM Rubber, End Cap Black Speed Bumps,~50mm Thickness, ~310mm Width x ~250mm Length/pc with slope, ~2.5kgs/pc

iv ) Model: RECY250X310, 100% EPDM Rubber with ~3mm Yellow Top Wear Layer, End Cap Yellow Speed Bumps,~50mm Thickness, ~310mm Width x ~250mm Length/pc with slope, ~2.5kgs/pc

RECOMMENDED Lag bolts:-

A) For concrete, use ½-inch diameter lag bolts and 4 to 5-inch in length

Disclaimer :
* Note : Users need to evaluate suitability for their industries use ( applications ) before placing order from us .